RGVTP.NET
Results 1 to 8 of 8

Thread: Engine and Transmission Torque Specs

  1. #1
    Join Date
    Nov 2007
    Location
    UNDER A TRUCK SOMEWHERE
    Posts
    9,867
    Post Thanks / Like

    Default Engine and Transmission Torque Specs

    Accelerator Control Cable Bracket Bolts 89 lb in
    Air Conditioning Compressor Bolts 37 lb ft
    Air Conditioning Compressor Bracket Bolts 37 lb ft
    Air Conditioning Idler Pulley Bolt 37 lb ft
    Air Conditioning Tensioner Bolt 18 lb ft
    Air Injection Reaction (AIR) Pipe-to-Exhaust Manifold Bolts 15 lb ft
    Camshaft Retainer Bolts 18 lb ft
    Camshaft Sensor Bolt 18 lb ft
    Camshaft Sprocket Bolts 26 lb ft
    Catalytic Converter Nut 18 lb ft
    Connecting Rod Bolts - First Design (First Pass) 15 lb ft
    Connecting Rod Bolts - First Design (Final Pass) 60 degrees
    Connecting Rod Bolts - Second Design (First Pass) 15 lb ft
    Connecting Rod Bolts - Second Design (Final Pass) 75 degrees
    Coolant Temperature Gauge Sensor 15 lb ft
    Crankshaft Balancer Bolt (Installation Pass-to Ensure the Balancer is Completely Installed) 240 lb ft
    Crankshaft Balancer Bolt (First Pass-Install a NEW Bolt After the Installation Pass and Tighten as Described in the First and Final Passes) 37 lb ft
    Crankshaft Balancer Bolt (Final Pass) 140 degrees
    Crankshaft Bearing Cap Bolts (Inner Bolts-First Pass in Sequence) 15 lb ft
    Crankshaft Bearing Cap Bolts (Inner Bolts-Final Pass in Sequence) 80 degrees
    Crankshaft Bearing Cap Side Bolts 18 lb ft
    Crankshaft Bearing Cap Studs (Outer Studs-First Pass in Sequence) 15 lb ft
    Crankshaft Bearing Cap Studs (Outer Studs-Final Pass in Sequence) 53 degrees
    Crankshaft Oil Deflector Nuts 18 lb ft
    Crankshaft Position Sensor Bolt 18 lb ft
    Cylinder Head Bolts (First Pass all M11 Bolts in Sequence) 22 lb ft
    Cylinder Head Bolts (Second Pass all M11 Bolts in Sequence) 90 degrees
    Cylinder Head Bolts (Final Pass all M11 Bolts in Sequence-Excluding the Medium Length Bolts at the Front and Rear of Each Cylinder Head) 90 degrees
    Cylinder Head Bolts (Final Pass M11 Medium Length Bolts at the Front and Rear of Each Cylinder Head in Sequence) 50 degrees
    Cylinder Head Bolts (M8 Inner Bolts in Sequence) 22 lb ft
    Cylinder Head Coolant Plug 15 lb ft
    Cylinder Head Core Hole Plug 15 lb ft
    Drive Belt Idler Pulley Bolt 37 lb ft
    Drive Belt Tensioner Bolts 37 lb ft
    Engine Block Coolant Drain Plugs 44 lb ft
    Engine Block Heater 30 lb ft
    Engine Block Oil Gallery Plugs 44 lb ft
    Engine Coolant Air Bleed Pipe Bolts and Studs 106 lb in
    Engine Crossmember Bolts (Large) 107 lb ft
    Engine Crossmember Bolts (Small) 92 lb ft
    Engine Flywheel Bolts (First Pass) 15 lb ft
    Engine Flywheel Bolts (Second Pass) 37 lb ft
    Engine Flywheel Bolts (Final Pass) 74 lb ft
    Engine Flywheel-to-Torque Converter Bolts 44 lb ft
    Engine Front Cover Bolts 18 lb ft
    Engine Mount Heat Shield Nuts 89 lb in
    Engine Mount Stud-to-Engine Block 37 lb ft
    Engine Mount Through Bolts 70 lb ft
    Engine Mount Through Bolt Nuts 59 lb ft
    Engine Mount-to-Engine Block Bolts 37 lb ft
    Engine Rear Cover Bolts 18 lb ft
    Engine Service Lift Bracket M10 Bolts 37 lb ft
    Engine Service Lift Bracket M8 Bolt 18 lb ft
    Engine Valley Cover Bolts 18 lb ft
    Engine Wire Harness Clip Bolt 37 lb ft
    Engine Wire Harness Ground Strap Bolt 37 lb ft
    Exhaust Gas Recirculation (EGR) Valve Bolts (First Pass) 89 lb in
    EGR Valve Bolts (Final Pass) 22 lb ft
    EGR Valve Pipe-to-Cylinder Head Bolts 37 lb ft
    EGR Valve Pipe-to-Exhaust Manifold Bolts 22 lb ft
    EGR Valve Pipe-to-Intake Manifold Bolt 89 lb in
    Exhaust Manifold Bolts (First Pass) 11 lb ft
    Exhaust Manifold Bolts (Final Pass) 18 lb ft
    Exhaust Manifold Heat Shield Bolts 80 lb in
    Exhaust Manifold Pipe Nuts 26 lb ft
    Front Shock-to-Engine Crossmember Bolts 48 lb ft
    Fuel Injection Fuel Rail Bolts 89 lb in
    Generator Bracket Bolts 37 lb ft
    Generator Rear Bracket-to-Engine Block Bolt 18 lb ft
    Generator Rear Bracket-to-Generator Bolt 18 lb ft
    Ground Strap Bolt (at Rear of Cylinder Head) 37 lb ft
    Ignition Coil-to-Bracket Bolts 106 lb in
    Ignition Coil Bracket-to-Valve Rocker Arm Cover Bolts 106 lb in
    Intake Manifold Bolts (First Pass in Sequence) 44 lb in
    Intake Manifold Bolts (Final Pass in Sequence) 89 lb in
    Knock Sensors 15 lb ft
    Oil Filter 22 lb ft
    Oil Filter Fitting 40 lb ft
    Oil Level Indicator Tube Bolt 18 lb ft
    Oil Level Sensor 115 lb in
    Oil Pan Baffle Bolts 106 lb in
    Oil Pan Closeout Cover Bolt (Left Side) 106 lb in
    Oil Pan Closeout Cover Bolt (Right Side) 106 lb in
    Oil Pan Cover Bolts 106 lb in
    Oil Pan Drain Plug 18 lb ft
    Oil Pan M8 Bolts (Oil Pan-to-Engine Block and Oil Pan-to-Front Cover) 18 lb ft
    Oil Pan M6 Bolts (Oil Pan-to-Rear Cover) 106 lb in
    Oil Pressure Sensor 15 lb ft
    Oil Pump-to-Engine Block Bolts 18 lb ft
    Oil Pump Cover Bolts 106 lb in
    Oil Pump Relief Valve Plug 106 lb in
    Oil Pump Screen Nuts 18 lb ft
    Oil Pump Screen-to-Oil Pump Bolt 106 lb in
    Oxygen Sensor 31 lb ft
    Positive Crankcase Ventilation (PCV) System Strap Nut (at Right Front Vapor Vent Pipe Stud) 106 lb in
    Power Steering Pump Bolts 18 lb ft
    Power Steering Pump Bracket Bolts 18 lb ft
    Spark Plugs (Cylinder Heads-New) 15 lb ft
    Spark Plugs (all Subsequent Installations) 11 lb ft
    Throttle Body Bolts 106 lb in
    Transmission Housing Bolt 37 lb ft
    Valve Lifter Guide Bolts 106 lb in
    Valve Rocker Arm Bolts 22 lb ft
    Valve Rocker Arm Cover Bolts 106 lb in
    Water Inlet Housing Bolts 11 lb ft
    Water Pump Bolts (First Pass) 11 lb ft
    Water Pump Bolts (Final Pass) 22 lb ft
    Water Pump Cover Bolts 11 lb ft


    4L60-E Transmission Torque Specs
    Application
    Spec
    Accumulator Cover to Case Bolt 6-10 lb ft
    Case Extension to Case Bolt 31-35 lb ft
    Case Extension to Case Bolt (4WD Shipping) 8.3-16.7 lb ft
    Converter Cover Bolt 89 lb in
    Converter Housing to Case Screw 48-55 lb ft
    Cooler Pipe Connector 26-30 lb ft
    Detent Spring to Valve Body Bolt 15-20 lb ft
    Floorshift Control Bolt 89 lb in
    Flywheel to Torque Converter Bolt 46 lb ft
    Forward Accumulator Cover to Valve Body Bolt 6-10 lb ft
    Heat Shield to Transmission Bolt 13 lb ft
    Line Pressure Plug 6-10 lb ft
    Manual Shaft to Inside Detent Lever Nut 20-25 lb ft
    Negative Battery Cable Bolt 11 lb ft
    Oil Level Indicator Bolt 35 lb ft
    Oil Pan to Transmission Case Bolt 97 lb in
    Oil Passage Cover to Case Bolt 6-10 lb ft
    Park Brake Bracket to Case Bolt 20-25 lb ft
    Park/Neutral Position Switch Screw 27 lb in
    Plate to Case Bolt (Shipping) 20-25 lb ft
    Plate to Converter Bolt (Shipping) 20-25 lb ft
    Plug Assembly, Automatic Transmission Oil Pan (C/K) 22.1-29.5 lb ft
    Plug Assembly, Automatic Transmission Oil Pan (Y) 20.7-23.6 lb ft
    Pressure Control Solenoid Bracket to Valve Body Bolt 6-10 lb ft
    Pump Assembly to Case Bolt 19-24 lb ft
    Pump Cover to Pump Body Bolt 15-20 lb ft
    Shift Cable Grommet Screw 15 lb in
    Shift Control Cable Attachment 15 lb ft
    Speed Sensor Retainer Bolt 7.7-10 lb ft
    Stud, Automatic Transmission Case Extension (Y-car) 13-16 lb ft
    TCC Solenoid Assembly to Case Bolt 6-10 lb ft
    Trans Mount to Transmission Bolt 18 lb ft
    Transmission Fluid Pressure Manual Valve Position Switch to Valve Body Bolt 6-10 lb ft
    Transmission Oil Cooler Pipe Fitting 26-30 lb ft
    Transmission Oil Pan to Case Bolt 7-10 lb ft
    Transmission to Engine Bolt 35 lb ft
    Valve Body to Case Bolt 6-10 lb ft


    T-56 Transmission Torque Specs
    Application
    Spec
    Backup Lamp Switch 20 lb ft
    Clutch Actuator Cylinder Bolt 71 lb in
    Clutch Housing Bolt 37 lb ft
    Control Lever Handle Bolt 18 lb ft
    Gear Select/Skip Shift Solenoid 30 lb ft
    Reverse Lockout Assembly Bolt 13 lb ft
    Reverse Lockout Solenoid 30 lb ft
    Shift Control Bolt 13 lb ft
    Shift Control Closeout Boot Bolt 18 lb in
    Shift Control Knob 27 lb ft
    Transmission Bolt 37 lb ft
    Transmission Drain/Fill Plug 20 lb ft
    Transmission Mount Bolt 38 lb ft
    Transmission Mount Nut 77 lb ft
    Transmission Support Bolt 66 lb ft
    Vehicle Speed Sensor Bolt 89 lb in


    Clutch Torque Specs
    Application
    Spec
    Brake Pedal Pivot Nut 40 lb ft
    Clutch Actuator Cylinder Bolt 71 lb in
    Clutch Pressure Plate Bolt (5-Speed) 15 lb ft + 45 degrees
    Clutch Pressure Plate Bolt (6-Speed) 52 lb ft
    Clutch Master Cylinder Nut 15 lb ft
    Transmission Bolt (5-Speed) 55 lb in
    Transmission Bolt (6-Speed) 37 lb ft
    4 wheels move the body, 2 wheels move the soul!!
    00 silverado
    2012 Chevy cruze RS
    2010 jeep jk Sahara 2dr
    07 gsxr750
    2013 gsxr1000 - #1308
    2008 gsxr 1000 stroker new project 7's or bust

  2. #2
    Join Date
    Nov 2007
    Location
    Edinburg, TX
    Posts
    4,833
    Post Thanks / Like

    Default

    Very good info...
    File Performance Tuning
    956.491.1017

    Now Doing Mail Order Tunes
    Ask me about any Installs you might need...

  3. #3
    Join Date
    Nov 2007
    Posts
    6,726
    Post Thanks / Like

    Default

    Great info I was thinking of posting GM part numbers for head gaskets and head bolt kits. They come in handy sometimes.
    2005 Silverado RCSB 443 stroker
    9.10 @ 150.78 mph Tuned by Me
    11.8 2013 mustang tuned by me



    [SIZE="5"]
    [B]Spike Performance
    Shop 9567832310
    Spike 9564573600
    We don't just talk we prove!!! SPT WHERE WE PROVE THE NUMBERS

  4. #4
    Join Date
    Nov 2007
    Location
    UNDER A TRUCK SOMEWHERE
    Posts
    9,867
    Post Thanks / Like

    Default

    orale if u want i can post it up let me know
    4 wheels move the body, 2 wheels move the soul!!
    00 silverado
    2012 Chevy cruze RS
    2010 jeep jk Sahara 2dr
    07 gsxr750
    2013 gsxr1000 - #1308
    2008 gsxr 1000 stroker new project 7's or bust

  5. #5
    Join Date
    Aug 2012
    Posts
    10
    Post Thanks / Like

    Default

    wow! its bit of lengthy but really a useful info. thanks for sharing.

  6. #6
    Join Date
    Aug 2012
    Posts
    10
    Post Thanks / Like

    Default

    i must say that you have done a great job of sharing this wonderful information. its very useful, thanks you.

  7. #7
    Join Date
    Nov 2007
    Location
    alton tx.
    Posts
    773
    Post Thanks / Like

    Default

    dam old ass thread 2008 lol but good info

  8. #8
    Join Date
    Apr 2012
    Location
    La casita tx
    Posts
    257
    Post Thanks / Like

    Default

    Good info
    6.0 LY6 L92 Heads 411 gears tuned by SPIKE.....

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •